Description
This anti-slip protection for your woods shields them from weather aggressions. Its highly effective formula contains non-slip microbeads based on propylene wax. Your wood is protected and maintains its original appearance. Easy to use, it is ideal for maintaining wooden surfaces on your boat.
Properties
Nourishing UV-reinforced protection combined with an anti-slip system for boat decks, pontoons, teak decks, and Ipe decks...
Light teak tint.
Light teak tint.
Destination
Exterior.
All wooden structures (new or old) used in the marine environment or elsewhere. Dense, exotic woods. Brushed or planed finish.
All wooden structures (new or old) used in the marine environment or elsewhere. Dense, exotic woods. Brushed or planed finish.
Recommendations before application
New wood:
Direct application. If the wood has significant surface glazing (which hinders product penetration), consider preparing the surface beforehand (consult us).
Untreated gray wood:
Clean with DECK CLEANER**. Sand the wood if necessary (100 grit).
Previously treated (oiled) gray wood:
Remove oil with AQUANETT®** + DECK CLEANER**. Sand the wood if necessary (100 grit).
Previously painted, stained, or varnished wood:
- Alkyd glycerophthalic coating: strip with MARINE STRIP** + DECK CLEANER**.
- Acrylic coating: consult us.
How to check if wood has excessive surface glazing?
Perform the water drop test to verify if wood is absorbent (open/glazed). Place a drop of water on the wood. If it does not penetrate, the wood is non-absorbent in its current state. Natural (sanding/brushing) or chemical (AQUANETT®**) deglazing is necessary.
The wood must be clean, dry (3 days of dry weather - maximum wood humidity 18%), sound, and prepared according to the standards in force - free from dust, mold, grease stains, and any old coating.
Do not apply in direct sunlight during the hottest hours of the day. Ensure no rain for 24/48 hours after application.
Relative humidity should be around 50% for optimal drying. Watch out for morning dew.
Protect anything that should not be treated.
Direct application. If the wood has significant surface glazing (which hinders product penetration), consider preparing the surface beforehand (consult us).
Untreated gray wood:
Clean with DECK CLEANER**. Sand the wood if necessary (100 grit).
Previously treated (oiled) gray wood:
Remove oil with AQUANETT®** + DECK CLEANER**. Sand the wood if necessary (100 grit).
Previously painted, stained, or varnished wood:
- Alkyd glycerophthalic coating: strip with MARINE STRIP** + DECK CLEANER**.
- Acrylic coating: consult us.
How to check if wood has excessive surface glazing?
Perform the water drop test to verify if wood is absorbent (open/glazed). Place a drop of water on the wood. If it does not penetrate, the wood is non-absorbent in its current state. Natural (sanding/brushing) or chemical (AQUANETT®**) deglazing is necessary.
The wood must be clean, dry (3 days of dry weather - maximum wood humidity 18%), sound, and prepared according to the standards in force - free from dust, mold, grease stains, and any old coating.
Do not apply in direct sunlight during the hottest hours of the day. Ensure no rain for 24/48 hours after application.
Relative humidity should be around 50% for optimal drying. Watch out for morning dew.
Protect anything that should not be treated.
Application
• Do not dilute before or during application. Mix thoroughly for 2 to 3 minutes with a suitable helical mixer. Repeat if necessary during application.
• Apply a coat of OWATROL®-ATG over the entire blade in the direction of the wood fibers.
• Let dry for a minimum of 6 hours (at 20°C and 60% RH) then apply a second coat. Complete drying in 24 hours.
• If applying with a spray gun, immediate smoothing is always recommended to improve penetration and give a uniform appearance.
• Fully cured: 5 days.
Putting a pontoon or boat deck into service: light traffic between 24 hours and 5 days. Normal traffic after 5 days.
Ambient temperature and relative humidity influence drying time.
• Apply a coat of OWATROL®-ATG over the entire blade in the direction of the wood fibers.
• Let dry for a minimum of 6 hours (at 20°C and 60% RH) then apply a second coat. Complete drying in 24 hours.
• If applying with a spray gun, immediate smoothing is always recommended to improve penetration and give a uniform appearance.
• Fully cured: 5 days.
Putting a pontoon or boat deck into service: light traffic between 24 hours and 5 days. Normal traffic after 5 days.
Ambient temperature and relative humidity influence drying time.
| Application temperature | +10°C to +30°C |
|---|---|
| Finish | Satin |
| Coverage per coat | 13 m²/l |